Vanity tops are small pieces of stone, but they collect more site problems than almost any other marble element. A basin that does not fit the cut-out, a tap hole in the wrong place or a splashback that clashes with a mirror can all lead to a replaced slab. Clear marble vanity top shop drawings prevent these issues and make approval faster for hotels, villas and offices across the UAE.
What the Drawing Must Show
A complete vanity package normally includes a plan of the top, front and side elevations, sections through the basin and edge, a splashback elevation and a schedule. Each view answers a specific question for the fabricator or installer.
Gather the Right Information First
- Sanitary ware data: the manufacturer's template or technical sheet for the basin, including cut-out size, corner radius and whether it is under-mounted, semi-recessed or counter-top.
- Tap and accessory data: tap hole diameter, spacing and whether the mixer is deck-mounted or wall-mounted.
- Site dimensions: measured wall-to-wall lengths and out-of-square corners.
- Joinery drawings: cabinet sizes, support positions and drawer clearances under the basin.
- Design intent: edge profile, thickness build-up, splashback height and finish.
Never draw a cut-out from a generic basin block. Use the actual product's dimensions, because two basins that look identical can differ by several millimetres.
Drafting the Plan View
- Draw the overall top at 1:1 with wall lines and any returns.
- Locate basin centres from a fixed reference such as the wall end or cabinet centreline, not from the stone edge alone.
- Draw cut-outs with exact radii and show whether edges are polished inside the cut.
- Show tap holes with diameters and centre distances from the basin edge and back wall.
- Mark any joints if the top is longer than a single slab, and keep joints away from basins.
Edge Profiles and Build-Up
Common edge options include eased, bevel, bullnose, half-bullnose and mitred apron edges that make a thin slab look thick. For a mitred apron, draw a section showing the top slab, the apron strip, the mitre angle and the adhesive joint. State the visible thickness clearly so the client knows what they are approving.
Splashbacks and Upstands
Draw splashback elevations with height, joint positions and cut-outs for sockets or mirrors. Coordinate with the mirror supplier so the mirror sits on or above the upstand as intended. If the design calls for a full-height marble wall instead, refer to the wall elevation drawings rather than duplicating information.
Support and Fixing Details
Stone is heavy and brittle. The drawing should show how the top is supported:
- On a cabinet carcass, with or without a sub-top.
- On concealed brackets fixed into the wall, with bracket spacing from the bracket supplier.
- On steel frames for floating vanities, coordinated with the joinery or metalwork contractor.
Areas around under-mounted basins are narrow and need careful support. Show basin clips or support rails as recommended by the basin manufacturer.
Waterproofing and Sealants
Note silicone joints at walls, around basins and at splashbacks, and specify a sanitary grade sealant colour that matches the stone. Where water can collect, such as at the back edge, detail a slight fall or an upstand that directs water back to the basin.
A Simple Vanity Schedule
Give each top a code, for example VT-01, and list room, size, thickness, stone, finish, edge profile, number of basins, basin model and tap holes. In hotel projects with many repeated bathrooms, this schedule becomes the fabricator's main checklist.
Checks Before Issue
- Basin model on the drawing matches the approved sanitary ware.
- Cut-outs dimensioned from fixed references.
- Tap holes coordinated with wall or deck mixers.
- Joints avoid basins and focal veins.
- Supports shown for every span and every overhang.
- Splashback heights coordinated with mirrors and electrical points.
A vanity top drawing that answers every one of these questions usually goes through approval on the first submission and gets fabricated without surprises.
Working With Templates on Site
Even with perfect drawings, many fabricators ask for a physical template once cabinets are installed, especially where walls are out of square. Note on the drawing that final dimensions will be confirmed by site template before cutting, and show which dimensions are fixed design values and which are site-verified. This keeps the approval process moving while protecting the stone from being cut to dimensions that no longer match the built carcass.
Frequently Asked Questions
Should basin cut-outs be done on site or in the factory?
Factory cutting from an approved drawing and template gives the most accurate result. Site cutting is generally kept for small adjustments only.
What edge profile is easiest to maintain?
Simple eased or small radius edges are easier to clean and less likely to chip than sharp square edges in busy bathrooms.
Do I need the basin template to draw the cut-out?
Yes. Use the manufacturer's template or technical sheet for the exact model so the cut-out fits without gaps.
Related Reading on ShoaibSite
- Marble Shop Drawings: Complete Guide for UAE Fit-Out Projects
- Shop Drawing Approval Process in Dubai
Written by Shoaib Hussan, Founder of D3DDD – Dubai 3D Design & Draft.
Instagram: @mxhaib
Need drawings or 3D? Visit d3ddd.com or email info@d3ddd.com.

ConversionConversion EmoticonEmoticon